How to avoid illegal operation of led wall washer installation and wiring method?
Indoor space or underground space, in many situations, the light is not very good. In the daytime, some are good, but it is almost dark at night, so we need to install lamps in suitable places. LED wall washers are also called LEDs. Line lights are mainly used on walls to outline the outline of large buildings. So what is the installation and wiring method of led wall washers? How to avoid illegal operations during installation? Don’t worry, let’s take a look at BENWEI LIGHTING.
led wall washer
Installation and wiring method of led wall washer:
1. Preparation
(1) Before installing the LED wall washer, solder the tin bar and soldering iron required by the LED lamp beads to the aluminum substrate for use when preparing to install it.
(2) Check the installation materials first, if there is any problem, you can negotiate a refund or exchange, and finally prepare the installation kit.
2. Check
In order to ensure the quality of the installation, check the soldered board again, and test whether it can be normally lit after power-on test, so as to avoid the situation that it does not light up after the soldering is completed, and it needs to be removed and connected again.
3. If the lamp can be normally lit, first coat the back of the aluminum substrate with heat-dissipating silica gel, and then put the board in the shell.
LED wall washer installation wiring method and installation precautions
4. Welding
(1) Solder the power cord to the positive and negative poles of the aluminum substrate, tie the two ends with tape, and be sure to fix it firmly when applying glue.
(2) During the glue filling process, the whole is evenly laid flat, do not tilt or tilt, which will affect the installation effect.
5. If you use glue, in the afternoon of the same day, remove the remaining account, and then block the glass and the two ends where the wall washer is installed.
6. Connect the wall washer after installation, pay attention to the outlet interface, don't make mistakes, it is best to connect one by one, after plugging in the male and female, install according to the reference manual.
7. When making the finished lamp, first power on, then turn on the switch to test, check whether it is on normally, if it is abnormal, re-test and adjust.
led wall washer
How to avoid illegal operations?
1. When installing and repairing the lamp, make sure that it can be operated only when the power supply is cut off.
2. The luminaire is only suitable for installation on the surface of non-combustible materials, and no matter when, heat insulation pads or similar materials cannot cover the surface of the luminaire.
3. The lamps should be wired correctly, the red wire is connected to the live wire, the green wire is grounded, and the blue wire is connected to the neutral wire, and ensure that it is firm.
4. After the lead-in wire enters the lamp through the lead-out coil, the lead-out coil should be tightened to prevent rainwater from penetrating into the lamp body through the lead-in lead and damage the electrical appliances when the lamp is used in an upside down state.
5. The environment where the lamp is used, there should be no corrosive, flammable and explosive media around.
6. The parts connecting the lamp bracket should be sturdy to prevent accidents caused by the use environment and other factors.
7. Applicable ambient temperature of the lamp: 10℃～35℃.
8. The power supply voltage is allowed to fluctuate within the range of 95% to 105% of 220V. Excessive fluctuations will affect the life, light efficiency, color rendering and normal start-up ignition of electrical appliances and light sources.
9. The lamp is assembled with 1W LED light source, the power of the light source is 12*1W, 18*1W, 24X1W, 36*1W.
10. The lamp protection screen is made of 3MM tempered glass material. If it is damaged, please send it back to the original factory for replacement and repair. Please do not replace it yourself.
11. In order to ensure the normal service life of the lamp, the lamp cannot work continuously for a long time during use. Generally, the power supply must be cut off in time for about 8 hours of normal use. After the lamp body cools down (about 20 minutes), the lamp can be re-ignited.
12. This lamp is a fully sealed type. After installation or maintenance, it must be ensured that its seal is in effect before it can be used. The protection grade of this lamp is IP65, and it cannot be used in places prone to stagnant water or underwater.
led wall washer
The above is an explanation of the knowledge about the installation and wiring methods of the led wall washer and how to avoid illegal operations. The content is for your reference only, and I hope it can be helpful to everyone.
