Precautions for safe use of LED purification lights:
1. Before installing and using the LED purification panel light, please confirm whether the LED panel purification light is damaged during transportation. If the purification panel light is damaged, it cannot be installed and used again. Contact the LED purification light manufacturer in time to keep it. Evidence, and then communicate after-sales, reissue damaged clean lamps.
2. After the LED clean panel light does not light up or the lamp beads are dead, if it is confirmed that the LED clean light is not caused by the installation error, please do not disassemble the light for repair. If the LED purification lamp has been disassembled, the LED purification lamp manufacturer will not replace or guarantee the LED purification lamp in the after-sales service. Therefore, please contact the LED flat panel purification lamp manufacturer in time. After communication, you need to send back the faulty LED purification lamp or accessories. The LED purification lamp manufacturer will arrange for professional engineers to repair and issue a customer complaint report for related problems.
LED purification light panel light installation engineering purification engineering lamps
3. The accompanying materials of the LED purification light are prohibited for children to play, especially small accessories, such as screws, rubber plugs and other small objects, please place them in a place that children cannot touch, so as to prevent children from accidentally eating them and causing health problems. After the LED purification lamp is powered on, children should not be allowed to touch it at will, which may cause dangerous situations. After the LED panel cleaning lamp is powered on for a long time, the temperature of the surface of the cleaning lamp body may exceed 60 degrees Celsius (enough to cause harm to the human body), so be sure not to touch the lit LED panel purification lamp at will.
4. Although the light of the side-emitting LED purification lamp is soft and not dazzling, do not look directly at the light-emitting surface of the LED purification lamp for a long time. Looking directly at the LED purification lamp for a long time will cause certain damage to the eyes.
5. When installing LED purification lamps, they should be placed in a place away from open flames or high temperatures. Although the use temperature of LED purification lamps is between -20 degrees Celsius and 50 degrees Celsius, that is only the limit of use temperature. If you work at low temperature or high temperature for a long time, it will affect the service life of LED purification lamps, so please do not use it for a long time at extreme temperatures. If you really need to use it at high temperature or low temperature for a long time, please consult the LED purification lamp manufacturer about the relevant performance of the LED purification lamp to obtain reasonable suggestions for use.
6. If the LED purification panel light exceeds the service life specified by the LED purification light manufacturer, it is recommended to re-maintain and check the electrical circuit. If it is found that the purification lamp is seriously aging, it is recommended to scrap it, so as to avoid potential safety hazards and cause losses.
LED purification light clean panel light laboratory installation clean engineering lamps
Maintenance and cleaning precautions for LED purification lights:
1. The driving power supply of the LED panel cleaning light uses a 220V access voltage, which is fatal. Therefore, before cleaning the LED cleaning panel light, please be sure to disconnect the power supply to avoid the danger of electric shock to the cleaning personnel.
2. When cleaning the LED purification lamp, please wring out the wet towel before wiping, otherwise the water stains will enter the interior of the LED purification lamp, which may cause a short circuit in the internal circuit of the LED purification panel lamp, which will lead to the burning of the LED lamp beads after power-on.
3. The surface of Junshuo LED purification lamp has been specially treated. If it is contaminated with dust or stains, just wipe it with a damp cloth to wipe it clean. For stubborn stains, the LED clean light can also be properly cleaned with soap, weak detergent or warm water.
When cleaning the LED purification panel light, please try not to use chemicals or corrosive cleaners. Although the surface of Junshuo LED purification lamp has been anti-corrosion treatment, it does not have a protective effect on every chemical, so if you do not understand the characteristics of chemical cleaners, try not to use a lot of chemical cleaners to clean LEDs Clean light.
Benwei Lighting is an LED Tube, LED flood light, LED Panel Light, LED High Bay, LED manufacturer with 12 years of experience. If you want to purchase a high-quality LED flood light or have a more in-depth understanding of the application of LED flood lights, please contact send us inquiry， our web: https://www.benweilight.com/.
