how to correctly install indoor LED light bar？
How to correctly install the indoor LED light bar, if you want to add color or delicate feeling for the room, LED is a good choice. LED large volume, even if you do not have any electrical experience, can be easily set up. A successful installation first requires some planning to ensure that the right length of LEDs and matching power supply are available. You can then connect or solder the LED to the purchased connector. Connectors are easier to use, but soldering is a better option for a more permanent way to connect the LED strip to the connector. This is done by gluing the LED in place on the back of the LED and then inserting it to enjoy the atmosphere it creates.
Install indoor LED light strip 1. Select LED and power supply
Measure the area where you plan to hang the LEDs. Rough estimate of how much LED lighting you will need. If you are installing LED lighting in different locations, measure each location so that you can reduce the lighting size later. Add the measurements together to estimate the total length of LED lighting you need to purchase. Before doing anything else, plan the installation. Try to sketch the area and indicate where the lights should be placed and nearby sockets to which they can be connected. Be sure to consider the distance between the nearest socket and the location of the LED light. Get longer lighting lengths or extension cords to fill gaps as needed. LED strips and other consumables are available online. Some department stores, home improvement centers and light retailers also ship them.
Install indoor LED lamp strip 2. Check the LED voltage
To see what kind of voltage they need. To purchase online, check the LED light bar or product label on the website. LEDs are 12V or 24V. In order for the LED to run for a long time, you must have a matching power supply. Otherwise, the LED will not have enough power to run. If you plan to use more than one strip or cut the LEDs into smaller strips, you can usually connect them to the same power source. A 12V light is perfect for most locations and uses less power. However, the 24V variety glows brighter and is longer.
Install indoor LED lamp strip 3. Determine the maximum power consumption of the LED strip
Each LED strip consumes a specific amount of power or electricity. It depends on the length of the strip. Check the product label to see how many watts are used for lighting per 1 foot. Then multiply the watts by the total distance of the strips you intend to install. For example, if you were to install 25 feet (7.6 m) of lighting that would require 5.12 watts per foot, then: 25 watts x 3 feet = 128 watts total. Keep in mind that measurements will vary depending on where you live. Double check to see if it is watt per meter or watt per foot. If the total wattage is listed on the product label, divide it by the total number of feet or meters in the reel. For example, if the strip's length of 24 watts is 5 ft (1.5 m), then: 24/5 = 4.8 watts/ft.
Install indoor LED light bar four, get the minimum quota
Multiply the power consumption by 1.2 to get the minimum power rating. The results will tell you how much power you must maintain to keep the LEDs powered. Since the LEDs may consume a little more power than you expect, add 20% to the total and use it as a minimum. In this way, the available power will never fall below the power required by the LED. For example, use a 25-foot (7.6-m) bar: 128 total wattage x 1.2 = 153.6 watts. The power supply should be at least 153.6 watts, otherwise the lamp will not work.
Install indoor LED light bar five, get the minimum Abe
Divide the power consumption by the voltage to get the minimum ampere. This last measurement is crucial for powering the new LED strip. The ampere, or ampere, measures the speed at which an electric current travels. If the current cannot move through a long strip of LED light fast enough, the light will dim or go out. Ampere ratings can be measured with a multimeter and can be estimated with a little math. For example, if you have a 12V LED using 128 watts of power: 128/12 = 10.66 amperes. To test the LED bar, touch the multimeter lead to the copper point of the LED. Be sure to set it to A.
The above is about how to correctly install the indoor LED light bar to share, I believe that after reading the above summary, we have had a certain understanding of this knowledge, want to know more about the installation of indoor LED light information, you can go to the customer service for consultation.
Shenzhen Benwei Lighting Technology Co., Ltd is a professional manufacturer in producing LED lighting products, Our main products T8 T5 LED Tube, LED Grow Light,Poultry LED Light,Tri-proof LED Light,LED Flood Light, LED Panel, LED Stadium Light, LED High Bay, LED Strip light, If you want to purchase a high-quality LED lighting products or have a more in-depth understanding of the application of LED lighting, please contact send us inquiry.
