The characteristics of the bracket lamp and purchasing skills How to install the fluorescent lamp bracket
The stent lamp is also a mainstream lighting fixture. The stent lamp is mainly composed of an "upper lamp cap structure" and a "bottom lamp tube structure"; an energy-saving electronic ballast is installed inside the combined structure; it is commonly used in the tooling industry Many people don’t know much about stent lights. What are the characteristics and purchasing skills of stent lights? How to install the fluorescent lamp bracket? Let's follow Benwei to find out.
Bracket light
The characteristics and purchase skills of bracket lights:
1. The characteristics of the bracket lamp:
The characteristic of the stent lamp is that a partition structure is added below the space between the upper joint structure and the energy-saving electronic ballast; and the lower joint structure is provided with a growth section cavity structure; and the outer wall of the cavity structure is increased in this section There are many through holes around it, which are used for multiple heat insulation, shunting, heat dissipation, and ensuring the normal service life of energy-saving lamps. Compared with other lighting fixtures, its main characteristics are:
1. The service life of the stent lamp can reach about 8000 hours, which is equivalent to 6 times that of ordinary bulbs.
2. Compared with ordinary fluorescent lamps, the stent lamp has lower power consumption and can save energy by about 70-80%.
3. The stent lamp adopts three-primary-color fluorescent powder tube, the lighting effect is very good, the light is not dazzling, and it is relatively fresh.
4. The stent lamp is relatively novel in appearance design, compact and beautiful in appearance.
It is precisely because the bracket lamp has so many characteristics, so the bracket lamp is very widely used in our lives. It can be installed in the home, such as halls, horizontals, kitchens, etc. In addition, in the major It is also common to use in the commodity supermarkets. There are many bracket lamp products on the market. If you want to choose high-quality bracket lamp products, you must master certain skills:
Second, the purchase skill of the bracket lamp:
1. When purchasing a bracket lamp, in order to eliminate the shadow at the junction of the bracket lamp and the bracket, it is best to choose a bracket lamp with transparent masks at both ends of the bracket lamp, and the edge of the bracket lamp should be a product that seamlessly connects. , So the lighting effect will be better.
2. When choosing a stent lamp, the service life of the stent lamp should also be considered. We know that in fact, many products have some inferior quality products on the market. When we choose a stent lamp, we should choose the bracket lamp interface to be copper core. Bracket lights.
3. It should also be noted that when purchasing, the power cord of the bracket of the bracket lamp must be purchased with a three-wire bracket lamp. In addition to safety, the three-wire bracket is actually a product that meets the national standard.
Bracket light
The above is a brief introduction about the characteristics and purchasing skills of the bracket lamp. I believe that after the above introduction, everyone will have a further understanding and understanding of the bracket lamp. Of course, the most used bracket lamp today is the fluorescent lamp bracket lamp. In addition to the purchase of bracket lamps, special attention must be paid to the installation of the bracket. How to install the fluorescent lamp bracket? Let's take a look at the following introduction:
How to install the fluorescent lamp bracket:
1. Fluorescent lamp bracket installation method:
1. Electronic rectifier type: There are six wires on the rectifier. Two wires are connected to the power supply at one end, and four wires are connected to the other end. They are distinguished by two colors. These four wires are connected to the tube socket of the fluorescent lamp, but they must be Connect one group by one group, not cross.
2. There is a "cover" on the upper side of the lamp holder. Remove it upwards to expose the wires, ballasts, fixing screws, etc. Cut the wires, unscrew the screws, and the whole lamp holder is removed from the wall.
3. Iron core rectifier: The connection method is roughly the same as the above, except that a set of break (cannot cross) is taken on the pins at both ends of the lamp, and the two wires after the break are connected to the two ends of the starter seat respectively. Can.
4. When installing, you should fasten the wide side to one side of the light-emitting mask, and the narrow side to the lampshade. You have to connect one head of the ballast to the switch (fire wire) and the other end to the foot of one end of the lamp. (It is 1 end and 1 pin), (connect the neutral wire to the pin on the other end of the lamp (2 end and 1 pin), and connect the starter to the two ends of the lamp. 2 feet will do.
2. Precautions for installation of fluorescent lamp bracket:
1. Before installing the lamp, it is best to connect the lamp first and confirm that the lamp will be on before installing it, to prevent the trouble of checking after the lamp does not turn on due to transportation or other reasons after installation.
2. When installing or removing the fluorescent lamp bracket when power is on, stand on a wooden stool, wear gloves, and be careful not to touch walls and conductive objects including other people during operation.
